Good day my friends
I continue to write a series of articles on repair our favorite wings.
We sell a lot of them and they periodically break. Some customers are changing to new – and some repair by themselves. For them we are doing all of these instructions.
 |
| Smart led light up rainbow isis wings in action |
As usual, after the failure, we ask the client to send the video to a malfunction. And the customer sent to us this video:
In this video we can see that part of the wing is operating normally and the other part is not. We see the light noise. This item 3.1 or 3.2 of the repair manual on first look. Because the working part of the wing, and the other part is not working.
3.1 – Damaged control wire between the two LEDs.
3.2 – LED factory defect – and he stopped to send a control signal to the next LED.
We first consider Paragraph 3.1
 |
| Firstly turn on wings |
 |
| Try to find the last normal working LED in the chain |
 |
| After the last working LEDs we found broken wire |
 |
| Sometimes it can be a broken wire inside the containment, but it can be pulled out and wire will come out |
 |
| For fix you need some soldering equipment and parts from repair kit |
You need next equipment for work:
- Solder iron
- Solder
- Wire cutter
- Repair kit
 |
| Separate LEDs on the wing |
 |
| You see the LED in the containment |
 |
| Carefully cut off the shell |
 |
| Like this |
 |
| Touch a soldering iron to the shell and heat the glue inside |
 |
| When the glue is warmed up, it will become soft – just pull the shell down |
 |
| Cut shell remnant |
 |
| From torn wires must be removed shell and prepare it for soldering |
 |
| Add at the end of the solder wire |
 |
| Like this |
 |
| Locate the LED leg without wires |
 |
| Attach the wire to the prepared leg of the LED |
 |
| And solder it |
 |
| Everything is ready – you need to restore the protective shell |
 |
| Cut one of the wires in the middle |
 |
| Prepare the ends of the wires to solder – as we did above |
 |
| Take the protective cover from the repair kit |
 |
| Add solder to ends of wires |
 |
| Like this |
 |
| Use shells, big for leds and small to cover wires |
 |
| Solder two wires together – as it was before |
 |
| Like this |
 |
| Repeat for the second wire |
 |
| Repeat the same for the third wire |
 |
| Use the glue gun and Apply glue to the place of soldering |
 |
| Like this |
 |
| Pull the protective cover on the glue |
 |
| Repeat this for all three wires |
 |
| Use a soldering iron to heat up the protective shell |
 |
| Take a large protective shell |
 |
| And pull it to the LED |
 |
| Use a glue gun and Apply glue inside the containment |
 |
| From one side |
 |
| From second too |
 |
| Like this |
 |
| Use the plastic mounting of the repair kit, and attach the LED at its original place |
 |
| Like this |
 |
| Cut the rest by cutters |
 |
| Done |
 |
| After connecting, we see that both sides of the wing work |
Next consider Paragraph 3.2
The main difference is that you need to replace the LED. Sometimes factory marriage, and it can only be replaced.
Usually need to replace a malfunctioning first LED in the chain, but if that does not work you need to replace the last well-functioning LED.
The first stage is to remove the protective cover from the LED.
 |
| LED connection circuit |
It is very important – do not mix up the order of connection, be very careful and do everything strictly according to instructions or circuit diagram.
 |
| That’s what you need from the repair kit |
 |
| Take the prepared LED and see how it is soldered |
 |
| Cut the LEDs legs like on photo |
 |
| Like this |
 |
| Add solder to ends of legs |
 |
| Like this |
 |
| Take two LEDs so that the procedure for connecting the same (black dots inside the LEDs must be at the top) |
 |
| Unsolder first wire and solder it to the same place, but the new LED |
 |
| Like this |
 |
| Repeat with the next wire |
 |
| Like this |
 |
| And also with the third wire |
 |
| And also with the last wire |
 |
| Like this |
After all this – you need to put on the LED protective cover and test – how to do this can see above
We have completed the repair of torn wires, thank you for what you are spending your time on all this. You get a great experience and can correct such failure in the future on their own and very quickly.
That’s how they look at work:
Thank you for reading from all our team – EtereShop!!!
